Z6_EL9QHKG10GPM20IJGE61AK10O0
Z7_I8001C80M82D40A3IJJSN11012

S2K Commerce - Products Dropdown

Actions
Loading...
Z7_I8001C80MOVHE0AP2AJ17A3084

S2K Commerce - Shopping Cart

Actions
Loading...
Z7_EL9QHKG10GPM20IJGE61AK10S5

S2K Commerce - Order Entry

Actions
Loading...
Home  >  End-of-Arm Tooling  >  Specialty Grippers  >  Gimatic Electric Grippers  >  Gimatic MPLM - Two-Jaw Parallel Gripper  > 7270 Gimatic 2-Jaw Electric Gripper with Long Stroke MPLM

7270 Gimatic 2-Jaw Electric Gripper with Long Stroke MPLM

Item #:MPLM2535 
Available: Available upon Request

Gimatic electric grippers are designed to be used in place of traditional pneumatic components were compressed air circuits could be a liability. They operate in an on/off manner receiving their signal directly from a control panel. There is no programming needed or intermediary control device. An added benefit is the energy savings realized because the motor is only used to actuate the device. The actuator position is maintained by mechanical means when an object is gripped and motor cut off.
A microprocessor and all electronics are integrated into the gripper so that no other external controller is necessary. The microprocessor operates the motor and turns it off with no programming required.

1259.00
Each
Quantity:
  • 500g
  • Built in motor drive
  • Self–centering jaw system
  • 2x17.5mm Stroke
  • 22lbf Total gripping torque
  • T–slot style jaws for heavy loads
  • 24 volt DC with on/off signal from PLC
6282 Gimatic 3-Wire C-Slot PNP Sensor with M8 Connector

This sensor is the replacement for Part# SS3N203Y. The only difference is it does not come with the adapter for grippers with a T-slot.

Item #:
SS3N203G
31.16
Each
1882 Gimatic 3-Wire C-Slot PNP Sensor with 2.5m lead

This sensor is the replacement for Part# SS4N225Y. The only difference is it does not come with the adapter for grippers with a T-slot.

Item #:
SS4N225G
27.20
Each
8087 8-Pin Cable with 90° M8 Female Connector with lead, 200mm long

Ideal for DIY end effectors to be used on Collaborative Robots. Compatible with the QC-75 electrical connector. Can also be used with our entire line of electric grippers.

Item #:
CFGM890802P
33.88
Each
1884 Gimatic 3-Wire C-Slot NPN Sensor with M8 Connector

This sensor is the replacement for Part# SS3M203Y. The only difference is it does not come with the adaptor for grippers with a T-slot.

Item #:
SS3M203G
31.16
Each
1883 Gimatic 3-Wire C-Slot NPN Sensor with 2.5m lead

This sensor is the replacement for Part# SS4M225Y. The only difference is it does not come with the adapter for grippers with a T-slot.

Item #:
SS4M225G
27.20
Each
8017 Interface Plate to Mount Electric Grippers to Robot Robot Side For ISO9409-1-50-4-M6

Plate for mounting Mechatronic (Electric) grippers onto a robot with ISO 9409-1-50-4-m6 Interface

Item #:
MFI A374A
62.50
Each
8018 Interface Plate to Mount Electric Grippers to Robot Gripper Side For ISO9409-1-50-4-M6

Plate for mounting Mechatronic (Electric) grippers onto a robot with ISO 9409-1-50-4-m6 Interface

Item #:
MFI A374B
83.00
Each
8088 Short Double Connector 3-Pin M8 90° Female to 8-Pin 90° Female Connector

Allows direct connection from Gimatic 3-pin electric gripper to UR Tool I/O (wrist)

Item #:
CFGM8908CF8903010
33.51
Each