EMI MEX
216-535-4848
S2K Commerce - Products Dropdown
Actions
- ${title}
S2K Commerce - Shopping Cart
Actions
- ${title}
S2K Commerce - Order Entry
Actions
- ${title}
7702 Gimatic Mini Gripper with HNBR Pads & Sensor Slot
Non-marking HNBR pads for soft contact have a maximum temperature of 302°F. This new Sensor Slot position provides sensing without interfering with the part being gripped. Note: When trying to sense “sprue gripped” confirmation, the sensor will only send a signal when the gripper is actuated with compressed air.
- 57g
- Note, Unreliable sensing may occur if the part being gripped is less than 3mm. Correct sensor location in the slot is important for proper operation.
- 3–9mm Applicable Sprue
- Sensor sold separately, see 'Related Items' below.
- Gripper must be connected to compressed air to get a sprue gripped confirmation.
- ∅10mm diameter mounting post with M5 air port allows this gripper to be used with standard mounting and air connection components. Alternate M5 air port on front of gripper can be used.
- Single-acting with protected opening spring.
- Higher grip force than other similarly sized sprue grippers.
Gripper
Use Gimatic SSY sensors with new series S2 PB Grippers.
Use Gimatic SSY sensors with new series S2 PB Grippers.
Use Gimatic SSY sensors with new series S2 PB Grippers.
Use Gimatic SSY sensors with new series S2 PB Grippers.
Gimatic PRO-SSR sensors are digital magnetoresistive sensors with 2 programmable output signals: open, closed, and one that detects any position in the middle. The type of output can also be programmed (N.O. or N.C.) whereas type of the sensor (PNP or NPN) is set at the factory and cannot be changed.
Gimatic PRO-SSR sensors are digital magnetoresistive sensors with 2 programmable output signals: open, closed, and one that detects any position in the middle. The type of output can also be programmed (N.O. or N.C.) whereas type of the sensor (PNP or NPN) is set at the factory and cannot be changed.
Gimatic PRO-SSR sensors are digital magnetoresistive sensors with 2 programmable output signals: open, closed, and one that detects any position in the middle. The type of output can also be programmed (N.O. or N.C.) whereas type of the sensor (PNP or NPN) is set at the factory and cannot be changed.
Gimatic PRO-SSR sensors are digital magnetoresistive sensors with 2 programmable output signals: open, closed, and one that detects any position in the middle. The type of output can also be programmed (N.O. or N.C.) whereas type of the sensor (PNP or NPN) is set at the factory and cannot be changed.
Pads have snap in tabs. Dimensions: 22mm x 8mm, 2mm thickness.
This 3D printed (PA12 Nylon) bracket is an accessory that allows a OFC-14-10 Cylinder to be easily mounted to the body of a PB gripper. The OFC cylinder can be equipped with a few optional accessories intended to eject a runner stuck to the jaw of the gripper.
| No. | Part No. | Item Description | Qty Req. | Price | Qty |
| n/a | 107 M5 |
319 M5 Internal Hex Threaded Plug
|
0 |
1.25
Each
|
|
| n/a | AA 22 6 |
Replacement Magnet for many AA, DD & PB Gimatic Grippers
|
0 |
1.24
Each
|
|
| n/a | PB 0170 05 |
7484 Replacement HNBR Pad
|
0 |
5.28
Each
|
|
| n/a | PB 0013 20 |
Gimatic PB Gripper Replacement Main Spring
|
0 |
3.16
Each
|
|