S2K Commerce - Products Dropdown

- ${title}
S2K Commerce - Shopping Cart

- ${title}
S2K Commerce - Order Entry

- ${title}

- 30g
- A standard 15 Pin Sub D cable WGS CA can be used to connect the interface to the robot / EOAT
- Fits Senvex and Gimatic quick changers
- Adapter (Q#6743) needed for small size qc's
- Uses standard 15–pin D–sub cables
- Extra–strength Aluminum Housing
- Extra–strength Aluminum Housing
- A standard 15 Pin Sub D cable WGS CA can be used to connect the interface to the robot / EOAT
- Fits Senvex and Gimatic quick changers
- Adapter (Q#6743) needed for small size qc's
- Uses standard 15–pin D–sub cables
- Extra–strength Aluminum Housing
- Extra–strength Aluminum Housing
- 15 Pin Male End
- 1.5M Length
- Must Solder Ends
- 15–pin D–sub, VGA type
- 15 Pin Female End
- 1.5M Length
- Must Solder Ends
- 15–pin D–sub, VGA type
With the same mounting pattern as the tool flange of your cobot (ISO-9409-1-50-4-M6), you can mount any âPlug & Playâ end effector to the QC75-B for a quick and repeatable installation for every job. End effectors can be hard-wired to the QC75-B, or plugged to the wrist connector of your Cobot for even faster setup times.
- 18g
- 4 Integrated G1/8 pneumatic pass-through ports.
- Locked position sensing available.
- Optional electrical connector provides 16 screw terminals.
- Cobot insdustry standard ISO-9409-1-50-4-M6 mounting pattern.
- Handles both pneumatic and electrical end effectors.
- Air ports are integrated into the quick changer connection pins (patented) for streamlined pneumatic routing.
- Electrical connectors are integrated into the quick changer housing for streamlined wiring.
With the same mounting pattern as the tool flange of your cobot (ISO-9409-1-50-4-M6), you can mount any âPlug & Playâ end effector to the QC75-B for a quick and repeatable installation for every job. End effectors can be hard-wired to the QC75-B, or plugged to the wrist connector of your Cobot for even faster setup times.
- 18.5g
- 4 Integrated G1/8 pneumatic pass-through ports.
- Locked position sensing available.
- Optional electrical connector provides 16 screw terminals.
- Cobot insdustry standard ISO-9409-1-50-4-M6 mounting pattern.
- Handles both pneumatic and electrical end effectors.
- Air ports are integrated into the quick changer connection pins (patented) for streamlined pneumatic routing.
- Electrical connectors are integrated into the quick changer housing for streamlined wiring.
With the same mounting pattern as the tool flange of your cobot (ISO-9409-1-50-4-M6), you can mount any âPlug & Playâ end effector to the QC75-B for a quick and repeatable installation for every job. End effectors can be hard-wired to the QC75-B, or plugged to the wrist connector of your Cobot for even faster setup times.
- 15g
- 4 Integrated G1/8 pneumatic pass-through ports.
- Locked position sensing available.
- Optional electrical connector provides 16 screw terminals.
- Cobot insdustry standard ISO-9409-1-50-4-M6 mounting pattern.
- Handles both pneumatic and electrical end effectors.
- Air ports are integrated into the quick changer connection pins (patented) for streamlined pneumatic routing.
- Electrical connectors are integrated into the quick changer housing for streamlined wiring.
- 20g
- Sensor ready – purchase separately
- Note, Lock unit ONLY works with newer model Gimatic Quick Changers that have a threaded hole.
- 30g
- A standard 15 Pin Sub D cable WGS CA can be used to connect the interface to the robot / EOAT
- Fits Senvex and Gimatic quick changers
- Adapter (Q#6743) needed for small size qc's
- Uses standard 15–pin D–sub cables
- 30g
- A standard 15 Pin Sub D cable WGS CA can be used to connect the interface to the robot / EOAT
- Fits Senvex and Gimatic quick changers
- Adapter (Q#6743) needed for small size qc's
- Uses standard 15–pin D–sub cables
- 15–pin D–sub, VGA type
- 15–pin D–sub, VGA type
- Must wire directly to the PCB terminal module
- Fits Senvex and Gimatic quick changers
- Adapter (Q#6743) needed for small size qc's
- Must wire directly to the PCB terminal module
- Fits Senvex and Gimatic quick changers
- Adapter (Q#6743) needed for small size qc's
- This adaptor is needed for small size quick changers when using electrical connectors
- 53g
- The two parts (robot side and EOAT side) are provided separately
- They can be used on the left or right side
- Suitible for vacuum and compressed air
- 53g
- The two parts (robot side and EOAT side) are provided separately
- They can be used on the left or right side
- Suitible for vacuum and compressed air
- Up to 255 identifiable tools
- Binary coding of tools by means of 8 digital outputs 24Vdc.
- Generates a maintenance warning signal once the tool reaches a preset number of cycles
- Up to 255 identifiable tools
- Binary coding of tools by means of 8 digital outputs 24Vdc.
- Generates a maintenance warning signal once the tool reaches a preset number of cycles
- 7g
- For large size SWH-150 / Quick# 3831 & 3832
- Reference: 1-025-15-00
- 6g
- For small size SWH-50 / Quick# 3815 & 3816
- Reference: 1-025-05-00
- 6g
- For small size SWH-50 / Quick# 3816
- Use with inductive sensors
- Sensor bracket mounts on the EOAT or Robot side of QC
- Sensor signals when QC lock is engaged.
- Reference: 1-024-05-00
- 7g
- For regular and large size SWH Quick Changers
- Use with inductive sensors
- Sensor bracket mounts on the EOAT or Robot side of QC
- Sensor signals when QC lock is engaged.
- Reference: 1-024-09-00
- Use this spacer with low–profile electrical connectors and large size quick changers
- Must order spacer #504 if using with a large size quick changer
- Must order spacer #504 if using with a large size quick changer